X

Palm Paddle on a KX3? No problem!

Palm Paddles on a KX3

Well, I bit the bullet back in March, caved in and ordered a KX3 kit. It arrived August 9th via my friendly postlady and was on the air that evening. Overall the build process was painless – maybe 3.5 hours to complete without working very hard.

One of the major reasons for purchasing the radio was SOTA activations, primarily using CW (Morse code). The radio was a major purchase and since I already own a set of Palm Mini Paddles I chose not to order the Elecraft paddles that screw directly to the front of the transceiver.

Of course the magnetic base of the Mini Paddles does not work very well on the KX3’s aluminum case. A quick internet search didn’t turn up an ‘aluminum magnets’ so I was forced to find a different solution. I mocked up a cardboard version of a thin steel end panel that would slip over the RH side of the KX3 and held in place by the thumb screws. I took a few photos and bounced the idea off Frandy/N1FJ, Jeff/NT1K and Barry/N1EU.

First idea, scrapped quickly the following morning!

After sleeping on it I thought it could be accomplished more simply by a single strip of steel, perhaps stuck to the radio with double stick tape. I opened up my email and Frandy had already done the deed, using one of those metal strips that mounts electrical boxes in sheet rock. They’re called ‘F’ brackets, or by the slang term ‘battleships’. Damn, I have a bunch of those in stock, why didn’t I see them last night?

Anyway, a half hour later or so my Palm Paddles are mounted neatly on the RH side of the rig. I choose to counter sink the screw holes and use slightly longer FH screws (1/4″) to mount the steel strip, a sturdy method and still allows dis-assembly without having to peel off the strip. I could have elected to drill the holes larger than the bolt heads, and use double stick tape with the same result. I guess I just like to screw things together!

Here’s a short step by step of the process. The battleships cost maybe 25 cents, there were extra screws in the spare parts bag that fit perfectly, total time maybe 1/2 hour or so. I still may send my strip to the paint shop (rattle can) – but not today. We’re going on an activation tomorrow!

First, find yourself a ‘battleship’ and modify. Most any hardware store/home center will have these in their electrical department.

A ‘battleship’ ready for modification.

Cut where indicated, drill to fit, file the edges to a nice shape. Polish with one of those 3-M finishing pads, paint to match if desired. Sorry for the reflection in the photo, there is a vertical cut line just to the left of the ‘cut at arrows’. The easiest thing to do is remove the side panel from the KX3 and use it as a template.

Mounted on the RH side of the KX3

I added a piece of vinyl electrical tape on the back (not shown) so it won’t mar the case, then took out the original screws and attached the strip with two 1/4″ long screws that came in the spare parts bag. The original screws will just fit but I had these so why not use them?
Warning! Choose your screw length carefully, you don’t want them to extend too far into the KX3 and cause damage!

Another view of the paddles on the KX3

That’s all there is too it. Less than $1 in materials, maybe an hours time and your Palm Mini Paddles are ready to make lots of CW QSO’s Thanks to Frandy, Barry & Jeff for all their ideas.
Jim/KK1W


Comments

6 responses to “Palm Paddle on a KX3? No problem!”

  1. An alternative to double stick tape is 3M Dual Lock. They don’t leave any residue if removed and also allow you to reposition the paddles like the magnets. I use this to attach my paddles to a wooden lap table when operating from the living room couch.

  2. Excellent “outside the box” thinking!

  3. Thanks Jim, saved me the trouble of seeking out ‘aluminum magnets’

    73 – Rob

  4. Wouldn’t some two sided mounting tape been easier?

    1. Sure would Buck, this is for the folks that don’t want to put ‘sticky stuff’ on their radio. You also get the added benefit of being able to position the paddle at slightly different angles or easily remove it when you pack the radio. It isn’t the solution for everyone but what worked for us. Thanks for the comment.

    2. One of our challenges was to not get any sticky stuff on the rig.

Leave a Reply to Buck Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.